Product Disclaimer Information

Urbex® Textured Paving

 

Paving should be bedded on a full bed of mortar. Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365.Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.  Although performance is good, sizes and colours will be limited, and finish may be varied.    Sizes listed assume a minimum of a 10mm joint width.  Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product. Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area. We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced. All building materials should be protected from bad weather, both during storage and after initial installation.   Movement joints should be considered for large areas

 

Standard Pimple Paving & Urbex® Riven Paving

Paving should be bedded on a full bed of mortar. Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365. Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.  Although performance is good, sizes and colours will be limited, and finish may be varied.  Sizes listed assume a minimum of a 10mm joint width.  Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product.

Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area.

We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced.

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas

SYMPHONY® Lapis, SYMPHONY® Elements Metallic, Ardara & SYMPHONY® Urban

There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.

A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.

Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.

Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.

Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.

All building materials should be protected from bad weather, both during storage and after initial installation.

Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of jointing product.

When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.

Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.

For perfect results these products require appropriate cutting tools and correct installation techniques.

Movement joints should be considered for large areas.

 

SYMPHONY® Plus Driveway & SYMPHONY® Plus Natural

This product comes with specific installation guidelines.

When using SYMPHONY® Plus, mechanically aided lifting is essential due to the weight of the units.

SYMPHONY® Plus should be jointed using Polymeric Sand, Tempo should be jointed using Marshalls Exterior Jointing Grout.

 

Marshalls Exterior Jointing Grout

* Depending on humidity and temperature Not recommended for use with Drivesys® or products on a flexible bed. Minimum 20mm joint depth for paving. ** Based on Sawn Versuro 560 x 560 with a joint width of 10mm. Contact us for our handy tool to help calculate how many tubs you will need for your job. 12 month shelf life from date of manufacture Contact technical for further information advice.

 

Natural Slate

 

*Due to naturally splitting surface, thickness is between 18-24mm

 

Fairstone Cropped Granite Setts

*Please note Granite Setts are crated by weight so quantities are a guide only.

Sizes and coverage are those attained when laid with a 10mm joint.  The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur. As Granite is a natural material, varying degrees of quartz veining may be apparent in some pieces.

 

Please note due to the nature of this product significant variation between stones can occur.

The use of the correct installation method is critical for this product. To be installed smooth side down. Please note Marshalls Weatherpoint is not suitable for use with this product. Marshalls Exterior Jointing Grout should be used instead. (This product should only be used by experienced installers and is not for DIY application). Slurry back natural stone with Paving Primer to increase adhesion and prevent staining.

 

Tegula 60

 

*Tegula 60 palletised is made at our new state-of-the-art block plant, so pack sizes vary, the works covers postcodes DE, NG, LE, PE, NR, IP, CO CM, SL, HP, AL, SG, MK, LU, NN and OX. For full information see our specifications area or please ring our sales team to get a quote for your area. Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product. 
Mix blocks from a minimum of 3 of packs (if possible) to ensure the correct colour blend. 
Take blocks from vertical columns rather than horizontal layers unless otherwise stated.
Marshalls concrete block paving is manufactured at different factories therefore colour may vary slightly across these works of manufacture. Jointing sand should be introduced before the initial vibration and a rubber-faced matting on the vibrating plate should be used.

 

Indian Sandstone Circle

 

1 centre stone 8 inner rings 16 outer rings. The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

Paving should be installed on a full mortar bed. 
This product is not intended for driveways. 
Weatherpoint is suitable for jointing Indian Sandstone and Circles, Towngate, Antique Alverno and Flamed Narias.  
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone. In natural stone, iron spots can sometimes be identified after installation. This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone. 
All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas.

 

SYMPHONY® Jointing Compound

 

24 month shelf life from date of manufacture Contact technical for further information advice Minimum laying temperature of 3C

 

Tegula Walling

 

Assumes nominal 10mm joint width Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product. 

 

Marshalite® Rustic Walling, Marshalite® Pitched Walling & Marshalite® Split Walling

 

Assumes nominal 10mm joint width. Marshalite is faced on the front only but due to manufacturing process some ends may also be faced.

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.

 

Fairstone Sawn Sandstone Setts

 

Assumes nominal 10mm joint widthThe natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
Marshalls endeavour to ensure that all natural stone products are covered by the Fairstone guarantee of quality.
If the Fairstone Logo is visible on a product page be assured that this product is processed and supplied only by proven ethical sources.
Split setts require rigid installation and sawn can be laid either flexibly or rigid.
Due to the nature of this product, you may see some colour variation in natural stone products.  Where a full mortar bed install is recommended, coat the back of each block with Paving Primer before laying as this assist bonding and stop draw through from the bed.
The use of the correct installation method is critical for this product
Light coloured natural stone, whilst structurally sound for driveway use can emphasise tyre marks and oil spills. It must therefore be accepted that extra maintenance will be needed to
maintain the overall appearance. 

 

Weatherpoint® 365

 

Coverage is a guide based on a 450x450 plan size with 10mm joints at 35mm deep Minimum 20mm joint depth for paving 24 month shelf life from date of manufacture. Contact technical for further information advice.

 

Sika Sikaflex EBT Adhesive

 

Coverage: Up to 12m of a 5mm bead. In dabs: 1 cartridge covers 100 x 3cm dabs. In strips: 1 cartridge covers 12m with a 5x5mm cross section.

Drivesys® Jointing Compound

Drivesys® Jointing Compound is recommended for use with the Marshalls Drivesys® driveway system. Marshalls cannot guarantee the performance of this product with other driveway products. 

 

Drivesett Argent® Edging, Drivesett® Coping, Drivesett® 4 in 1 Kerb, Saxon® Edging ,Saxon® Copings, Heritage® Coping & Savanna® Kerb

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product. 

 

Drivesett® Tegula Original & Keyblok® 60

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product. 

Mix blocks from a minimum of 3 of packs (if possible) to ensure the correct colour blend. 

Take blocks from vertical columns rather than horizontal layers unless otherwise stated.

Marshalls concrete block paving is manufactured at different factories therefore colour may vary slightly across these works of manufacture.

Jointing sand should be introduced before the initial vibration and a rubber-faced matting on the vibrating plate should be used.

 

Drivesys® Flamed Stone

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product. 

Mix blocks from a minimum of 3 of packs (if possible) to ensure the correct colour blend.

Take blocks from vertical columns rather than horizontal layers unless otherwise stated.

Marshalls concrete block paving is manufactured at different factories therefore colour may vary slightly across these works of manufacture.

Drivesys Jointing Compound should be used on all Drivesys products.

Drivesys blocks initially have a transportation sealant on them which will weather away to show the true face of the block over a short period of time.

 

Modal X® Smooth, Modal X Priora® Textured, Modal X® Textured, Croft Stone® Walling, Tegula Kerb, Driveline® 4 in 1 Kerb, Round Top Edging, Argent® Walling, Argent® Coping / Edging, Lunar®& Savanna® Linear

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.  

 

Savanna®, Standard Concrete Block Paving, Driveline Nova® Coarse, Driveline Nova® Smooth, Drivesett Natrale®, Driveline Priora®, Drivesett Tegula Priora®

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.  

Mix blocks from a minimum of 3 of packs (if possible) to ensure the correct colour blend. 

Take blocks from vertical columns rather than horizontal layers unless otherwise stated.

Marshalls concrete block paving is manufactured at different factories therefore colour may vary slightly across these works of manufacture.

Jointing sand should be introduced before the initial vibration and a rubber-faced matting on the vibrating plate should be used.

 

Drivesys® Riven Stone & Drivesys® Original Cobble

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.  

Mix blocks from a minimum of 3 of packs (if possible) to ensure the correct colour blend.

Take blocks from vertical columns rather than horizontal layers unless otherwise stated.

Marshalls concrete block paving is manufactured at different factories therefore colour may vary slightly across these works of manufacture.

Drivesys Jointing Compound should be used on all Drivesys products.

Drivesys blocks initially have a transportation sealant on them which will weather away to show the true face of the block over a short period of time.

 

Richmond® Utility Paving, Textured Utility Paving & Woodstone® Paving

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.

Paving should be bedded on a full bed of mortar.

Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365.

Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.

Although performance is good, sizes and colours will be limited, and finish may be varied.  

Sizes listed assume a minimum of a 10mm joint width.

Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product.

Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area.

We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced.

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas

 

Argent® Smooth Paving

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.

Paving should be bedded on a full bed of mortar.

Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365.

Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.

Although performance is good, sizes and colours will be limited, and finish may be varied.  

Sizes listed assume a minimum of a 10mm joint width.

Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product.

Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area.

We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced.

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas

Heritage® Paving

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.

Paving should be bedded on a full bed of mortar.

Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365.

Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.

Although performance is good, sizes and colours will be limited, and finish may be varied.  

Sizes listed assume a minimum of a 10mm joint width.

Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product.

Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area.

We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced.

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas

 

Pendle Utility Paving, Saxon® Paving & Firedstone® Paving

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.

Paving should be bedded on a full bed of mortar.

Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365.

Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.

Although performance is good, sizes and colours will be limited, and finish may be varied.  

Sizes listed assume a minimum of a 10mm joint width.

Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product.

Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area.

We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced.

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas

 

Perfecta® Paving & Argent® Coarse Paving

 

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product.

Paving should be bedded on a full bed of mortar.

Utility, Urbex, Textured Utility, Standard Pimple, Saxon, Richmond, Perfecta, Pendle and Argent paving should be jointed using traditional mortar or Weatherpoint 365.

Woodstone, Firedstone and Heritage should be jointed only with a traditional mortar mix.

Although performance is good, sizes and colours will be limited, and finish may be varied.  

Sizes listed assume a minimum of a 10mm joint width.

Concrete products are made from naturally occurring materials, which means these materials can vary in colour, resulting in a slight variation in a finished product.

Despite the use of quality materials, modern and up-to-date manufacturing techniques and quality control, variation between production batches can occur. Whilst any differences are generally quite minor, they will be noticeable when units from two production batches are laid consecutively within a single area.

We would always advise that batch codes are checked to reduce the risk of product variation and ensure consistency of finish. To prevent this, when multiple packs are being laid in one consecutive area, please ensure you check that they are all from the same production. The batch label will display the product code, with the first two letters identifying the works of origin and the week number indicating which week of the year the product was produced.

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas

Stoneface® Mixed Texture 

 

Min order 1 kit only. 1 kit will contain box A B and C

 

SYMPHONY® Matte

 

NOTE: Sizes and coverage are those stated with a 5-8mm joint.
There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.
A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.
Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.
Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.
Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.
All building materials should be protected from bad weather, both during storage and after initial installation.
Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of jointing product.
When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.
Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.
For perfect results these products require appropriate cutting tools and correct installation techniques.
Movement joints should be considered for large areas

 

Marshalls Exterior Tile Grout

 

Only recommended for use with porcelain and granite paving.  Contact us for our handy tool to help calculate how many tubs you will need for your job. 24 month shelf life from date of manufacture.

 

Stoneface® Drystack Veneer Walling & Stoneface® Sawn Veneer Walling

 

Product comes supplied with adhesive and primer

 

Marshalls Paving Primer

Recommended for use with Natural Stone and Porcelain paving.

 

Sika Primer 3

 

Sika Primer-3 N must be used within a month after opening the container. Discard any primer that has gelled.

 

Fairstone Traditional Pitch Faced Walling & Fairstone Traditional Tumbled Walling

 

Sizes and coverage are those attained when laid with a 10mm joint.

 

Fairstone Sawn Versuro® Jumbo

 

Sizes and coverage are those attained when laid with a 10mm joint.
Jumbo Sawn is delivered Direct to Site only on a kerb-side drop. Mechanical aided lifting is essential for the movement of this product
Paving should be installed on a full mortar bed.
This product is not intended for driveways.
This paving is ideal for jointing with Marshalls Exterior Jointing Grout.  
Marshalls Exterior Jointing Grout should be used by experienced installers and not for DIY application. 
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone.
In natural stone, iron spots can sometimes be identified after installation.  This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone.  
When using Jumbo and King Size, due to the weight of the units mechanically aided lifting is essential. 
Please note Jumbo and King Size can only be delivered direct to site.   
All building materials should be protected from bad weather, both during storage and after initial installation.  
Movement joints should be considered for large areas 

 

Fairstone Sawn Versuro® King Size

 

Sizes and coverage are those attained when laid with a 10mm joint.

King Size Sawn is delivered Direct to Site only on a kerb-side drop. Mechanical aided lifting is essential for the movement of this product  Paving should be installed on a full mortar bed. This product is not intended for driveways.  This paving is ideal for jointing with Marshalls Exterior Jointing Grout.    Marshalls Exterior Jointing Grout should be used by experienced installers and not for DIY application. 

Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone.
In natural stone, iron spots can sometimes be identified after installation.  This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone.    When using Jumbo and King Size, due to the weight of the units mechanically aided lifting is essential.   Please note Jumbo and King Size can only be delivered direct to site.     All building materials should be protected from bad weather, both during storage and after initial installation.  Movement joints should be considered for large areas
 
The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

 

Fairstone Limestone Aluri 

 

Sizes and coverage are those attained when laid with a 10mm joint.

Please note Charcoal Limestone is calibrated to 22mm thickness and Rustic Ochre Multi is calibrated to 25mm
 
Slurry back natural stone to increase adhesion and prevent staining.
All building materials should be protected from bad weather, both during storage and after initial installation.   Movement joints should be considered for large areas.
 
 
The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

 

Fairstone Antique Alverno®

Sizes and coverage are those attained when laid with a 10mm joint.

The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
Paving should be installed on a full mortar bed. 
This product is not intended for driveways.  
Weatherpoint is suitable for jointing Indian Sandstone and Circles, Towngate, Antique Alverno and Flamed Narias.   
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone. In natural stone, iron spots can sometimes be identified after installation. This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone.  
All building materials should be protected from bad weather, both during storage and after initial installation.  
Movement joints should be considered for large areas. 

 

Fairstone Sawn Versuro® Linear

 

Sizes and coverage are those attained when laid with a 10mm joint.
 
The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
Paving should be installed on a full mortar bed.
This product is not intended for driveways.
This paving is ideal for jointing with Marshalls Exterior Jointing Grout.  
Marshalls Exterior Jointing Grout should be used by experienced installers and not for DIY application.  
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone.
In natural stone, iron spots can sometimes be identified after installation.  This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone.  
When using Jumbo and King Size, due to the weight of the units mechanically aided lifting is essential. 
Please note Jumbo and King Size can only be delivered direct to site.   
All building materials should be protected from bad weather, both during storage and after initial installation.  
Movement joints should be considered for large areas

 

Sylvern® Limestone Paving

 

Sizes and coverage are those attained when laid with a 10mm joint.

The natural origin of stone means variation in colour, texture, and natural markings are inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
 
Slurry back natural stone to increase adhesion and prevent staining.
All building materials should be protected from bad weather, both during storage and after initial installation. 
Movement joints should be considered for large areas.

 

Fairstone Sawn Granite Setts

 

Sizes and coverage are those attained when laid with a 10mm joint.

The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur

As Granite is a natural material, varying degrees of quartz veining may be apparent in some pieces.

Please note due to the nature of this product significant variation between stones can occur.

The use of the correct installation method is critical for this product.

To be installed smooth side down.

Please note Marshalls Weatherpoint is not suitable for use with this product. Marshalls Exterior Jointing Grout should be used instead. (This product should

only be used by experienced installers and is not for DIY application).

Slurry back natural stone with Paving Primer to increase adhesion and prevent staining.

 

Fairstone Sawn Versuro®

 

Sizes and coverage are those attained when laid with a 10mm joint.

The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
Paving should be installed on a full mortar bed.
This product is not intended for driveways.
This paving is ideal for jointing with Marshalls Exterior Jointing Grout. 
Marshalls Exterior Jointing Grout should be used by experienced installers and not for DIY application.
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone.
In natural stone, iron spots can sometimes be identified after installation.  This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone. 
When using Jumbo and King Size, due to the weight of the units mechanically aided lifting is essential.
Please note Jumbo and King Size can only be delivered direct to site.  
All building materials should be protected from bad weather, both during storage and after initial installation. 
Movement joints should be considered for large areas

 

Towngate

 

Sizes and coverage are those attained when laid with a 10mm joint.

The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

Paving should be installed on a full mortar bed.

This product is not intended for driveways. 

Weatherpoint is suitable for jointing Indian Sandstone and Circles, Towngate, Antique Alverno and Flamed Narias.  

Slurry back natural stone to increase adhesion and prevent staining.

The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone. In natural stone, iron spots can sometimes be identified after installation. This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone. 

All building materials should be protected from bad weather, both during storage and after initial installation. 

Movement joints should be considered for large areas.

 

Fairstone Slate Casarta®

 

Sizes and coverage are those attained when laid with a 10mm joint.

The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

 

Marshalls Indian Sandstone

 

Sizes and coverage are those attained when laid with a 10mm joint.
The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur. 
Paving should be installed on a full mortar bed. 
This product is not intended for driveways.  
Weatherpoint is suitable for jointing Indian Sandstone and Circles, Towngate, Antique Alverno and Flamed Narias.   
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone. In natural stone, iron spots can sometimes be identified after installation. This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone.  
All building materials should be protected from bad weather, both during storage and after initial installation.  
Movement joints should be considered for large areas. 

 

Scoutmoor® Setts

 

Sizes and coverage are those attained when laid with a 5mm joint. 
The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

 

Alvanley® Pavers

 

Sizes and coverage are those attained when laid with a 5mm joint. The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
Paving should be installed on a full mortar bed.
This product is not intended for driveways.  
Slurry back natural stone to increase adhesion and prevent staining.
The natural origin of stone means that variation in colour, texture and markings is inevitable and is an inherent characteristic of all natural stone. In natural stone, iron spots can sometimes be identified after installation. This is due to oxidisation of iron materials within the matrix of the stone. This does not affect the structural integrity of the stone. 
All building materials should be protected from bad weather, both during storage and after initial installation. 
Movement joints should be considered for large areas.

 

Fairstone Granite Eclipse®

 

Sizes and coverage are those attained when laid with a 6mm joint.
Larger sizes should be installed by professionals with correct lifting equipment
Granite is a natural material, varying degrees of quartz veining may be apparent in some pieces.
This paving is ideal for use with Exterior Tile Grout or Marshalls Exterior Jointing Grout  (This product should only be used by experienced installers and is not for DIY application).
We would advise the application of a temporary Stone Sealer before the application of the grout to maintain the finish to the paving.
Occasionally small micro-fissures can be apparent within Granite, these are not a sign of weakness and cause no issue technically to the stone.
Slurry back natural stone to increase adhesion and prevent staining. 
All building materials should be protected from bad weather, both during storage and after initial installation. 
Movement joints should be considered for large areas. 
The Paving should be installed smooth side down.
 
 The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

 

Fairstone Split Sandstone Setts 

 

Split and tumbled setts are calibrated Assumes nominal 10mm joint width The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.
Marshalls endeavour to ensure that all natural stone products are covered by the Fairstone guarantee of quality.
If the Fairstone Logo is visible on a product page be assured that this product is processed and supplied only by proven ethical sources.
Split setts require rigid installation and sawn can be laid either flexibly or rigid.
Due to the nature of this product, you may see some colour variation in natural stone products.
Where a full mortar bed install is recommended, coat the back of each block with Paving Primer before laying as this assist bonding and stop draw through from the bed.
The use of the correct installation method is critical for this product
Light coloured natural stone, whilst structurally sound for driveway use can emphasise tyre marks and oil spills. It must therefore be accepted that extra maintenance will be needed to
maintain the overall appearance. 

 

SYMPHONY® Natural

 

The 600 x 600 sizes feature a riven/textured finish, while the 600 x 1200 sizes and project packs have a smooth finish. To avoid inconsistencies in surface finish, it's best not to mix sizes; instead, opt for a project pack or cut down one size to combine them.
To simplify installation the correct amount of jointing compound is provided on all full-pack orders of Symphony products
There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.
A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.
Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.
Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.
Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.
All building materials should be protected from bad weather, both during storage and after initial installation.
Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of jointing product.
When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.
Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.
For perfect results these products require appropriate cutting tools and correct installation techniques.
Movement joints should be considered for large areas

 

Infinia® Block Paving & Infinia®

The innovative surface technology used in the manufacture of Infinia® effectively minimises colour variation batch to batch; however, complete elimination cannot be guaranteed. To prevent this, we advise product is from the same production for single consecutive areas and during installation, the material is thoroughly mixed on site, drawing from a minimum of three packs simultaneously where possible.

 

Casarta® Slate Steps, Granite Eclipse® Steps, Fairstone Sawn Versuro® Borders, Fairstone Sawn Versuro® Copings, Fairstone Sawn Walling & Fairstone Sawn Versuro® Steps

 

The natural origin of stone means variation in colour, texture and natural markings is inevitable. Whilst Marshalls strives to ensure the integrity of each natural stone range through expert hand selection, some variation may occur.

 

Arrento® Encore

 

There may be some colour variation between production batches. Batch codes, quantity, and colour should therefore be checked prior to installation.
A dry lay of this product is recommended before installing it onto the full mortar bed to ensure the best colour blend is achieved.
Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.
There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.
A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.
Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.
Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.
Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.
All building materials should be protected from bad weather, both during storage and after initial installation.
When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.
Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.
For perfect results these products require appropriate cutting tools and correct installation techniques.
Movement joints should be considered for large areas

Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.
Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.
All building materials should be protected from bad weather, both during storage and after initial installation.
Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of your chosen jointing product.
Sizes and coverage quoted are based on working dimensions, attained with a 5-8mm joint.
For perfect results, these products require appropriate cutting tools and correct installation techniques.

 

Arrento® Porcelain Paving

 

There may be some colour variation between production batches. Batch codes, quantity, and colour should therefore be checked prior to installation.

A dry lay of this product is recommended before installing it onto the full mortar bed to ensure the best colour blend is achieved.

Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.

There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.

A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.

Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.

Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.

Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.

All building materials should be protected from bad weather, both during storage and after initial installation.

Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of jointing product.

When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.

Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.

For perfect results these products require appropriate cutting tools and correct installation techniques.

Movement joints should be considered for large areas

Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.

Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.

All building materials should be protected from bad weather, both during storage and after initial installation.

Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of your chosen jointing product.

Sizes and coverage quoted are based on working dimensions, attained with a 5-8mm joint.

For perfect results, these products require appropriate cutting tools and correct installation techniques.

 

Arrento® Core

 

There may be some colour variation between production batches. Batch codes, quantity, and colour should therefore be checked prior to installation.
A dry lay of this product is recommended before installing it onto the full mortar bed to ensure the best colour blend is achieved.
Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.
There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.
A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.
Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.
Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.
Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.
All building materials should be protected from bad weather, both during storage and after initial installation.
When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.
Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.
For perfect results these products require appropriate cutting tools and correct installation techniques.
Movement joints should be considered for large areas

Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.
Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.
All building materials should be protected from bad weather, both during storage and after initial installation.
Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of your chosen jointing product.
Sizes and coverage quoted are based on working dimensions, attained with a 5-8mm joint.
For perfect results, these products require appropriate cutting tools and correct installation techniques.

 

Drivesys® Split Stone

 

This pack size is subject to change please call Marshalls on 0345 3040 707 for more information

Due to the nature of this product and the manufacturing process, some variation may occur. Where images are viewed online or in printed material, we cannot guarantee that the colours shown directly reflect the colours of the actual product. 

Mix blocks from a minimum of 3 of packs (if possible) to ensure the correct colour blend.

Take blocks from vertical columns rather than horizontal layers unless otherwise stated.

Marshalls concrete block paving is manufactured at different factories therefore colour may vary slightly across these works of manufacture.

Drivesys Jointing Compound should be used on all Drivesys products.

Drivesys blocks initially have a transportation sealant on them which will weather away to show the true face of the block over a short period of time.

 

Driveline Drain®

 

This product comes with specific installation guidelines. Please contact our Technical Advisory Team on 0370 411 2233 or visit our website prior to installation

 

SYMPHONY® Porcelain Plank Paving & SYMPHONY® Classic

 

To simplify installation the correct amount of jointing compound is provided on all full pack orders of Symphony products

There may be some colour variation between production batches. Batch codes, quantity and colour should therefore be checked prior to install.

A dry lay of this product is recommended before installing onto the full mortar bed to ensure the best colour blend is achieved.

Please make a note of the shade code of the product you have received. This will be advantageous if you need to place orders at a later date to complete a job as it will allow us to send the best match possible.

Customers should not mix different sizes of the same colour, as there could be colour/shade variation due to the different batches.

Porcelain paving, with the exception of the Plus range, must be primed with a Paving Primer before installing onto a full mortar bed.

All building materials should be protected from bad weather, both during storage and after initial installation.

Packs of Porcelain, with the exception of the Plus range, are supplied with just the right amount of jointing product.

When using Symphony jointing material, drainage ports must be incorporated to allow free draining from the joint to the sub-base.

Sizes and coverage quoted are based on working dimensions, attained when using the Porcelain Jointing Compound with a 3-5mm joint.

For perfect results these products require appropriate cutting tools and correct installation techniques.

Movement joints should be considered for large areas.