Go to Marshalls or explore Close
Looking for something different? View Commercial Landscaping Products
Accessories Technical Information
This guide runs through technical garden and driveway accessories information for the following products.
- Walling
- Stoneface walling
- Copings and caps
- Bullnose steps
- Kerbs and Edging
- Pedestals
- Borders
- Jointing
- Green-away patio cleaner
Walling
Common to all Marshalls Walling Products
Marshalls recommends the use of Copings and Caps with all Walling Products. They also protect walls against the staining effect of rain for a period of time.
Marshalls recommends the use of Copings and Caps with all Walling Products. They also protect walls against the staining effect of rain for a period of time.
Sawn Versuro
Faced on all sides.
An external thin bed adhesive is recommended.
Sizes and coverage quoted are based on working dimensions, attained with a 5mm joint.
Traditional Natural Stone
A 10mm joint width is recommended with this product.
Due to tolerance of product, some sorting will be required before commencing installation.
For use in constructing a wall no more than 1.5m in height.
Pitched Face Walling is faced on one side and two ends. Tumbled Walling is faced on all sides. Sizes and coverage quoted are based on working dimensions.
Specific installation guidance must be followed. Consult a Marshalls Accredited Installer. Or for further guidance contact Group Technical Services.
Argent
Please note this walling is only faced on one side.
Corner Quoin Ends can be ordered via Marshalls Split Pack Service.
An external thin bed adhesive is recommended.
Sizes are actual, with coverage attained assuming a 10mm joint width.
Croft Stone
This walling is ideal for retaining walls up to 6 courses, but should never be used as a freestanding or dividing wall.
Minimum radius that can be created is 750mm on the bottom course.
Please Note: This product cannot form a right angle.
Sizes and coverage are actual and do not include joint width. For number of units required per linear measure please see website.
Marshalite
A 10mm joint width is recommended with this product.
Product is faced on 1 side, Quoin ends are not available.
Tegula
A 10mm joint width is recommended with this product.
Phoenix Facing Brick
A 10mm joint width is recommended with this product.
Walling
Common to all face Veneer Walling Products:
Where a facing/veneer wall is used with garden/soil/planting/aggregates behind it, a membrane must be installed at the rear of the wall to stop moisture draw through.
Walls over 1.5m high need mechanical fixing.
The correct drainage (such as weep holes) should be considered for any walling retaining soil.
Stoneface Sawn Veneer
1.5m height before mechanical fixing is needed.
Stoneface Drystack Veneer
Panels are in a Z cut format to hide joints, for a seamless finish. Please note there is a slight tolerance in this and some units will require some minor modification to reduce gaps.
Thickness calibrated to 15mm +/- 1.5mm.
Copings & Caps
No drip grooves are included in our range of copings.
Bullnose steps
Casarta Slate steps are 40mm thick.
Kerbs & Edging
The perfect edge restraints to co-ordinate with the Driveway products or contrast with other products within the Driveways range.
Tegula and Savanna Kerb have a 45o splay.
Smallest radius for an internal kerb is 0.46m.
Smallest radius for external kerb is 0.62m.
When laying Keykerb, KL protrudes 100-125mm and KS by 25-50mm.
Specific installation guidance must be followed. Consult a Marshalls Accredited Installer. Or for further guidance contact Group Technical Services.
Marshalls 4 in 1 kerb and Block Kerb are manufactured across the UK so colour variation may alter slightly to images represented.
Pedestals
For best results, ensure you use the rubber base pads on the sub-base to keep the pedestals in place and rubber head pads on the head of the pedestal to reduce noise and minimise movement of the paving units.
If laying porcelain paving onto a roof terrace or where wind loading may be a concern, apply a small dab of Sika EBT onto both sides of the rubber head pads before installing the paving unit to minimise movement.
Roughly lay out sufficient pedestals for 4 or 5 paving units at a time.
For corner units, or when a cut would otherwise reduce the paving unit to half of its original size, reduce the pedestal size by cutting along the bottom of the base unit.
Lay the paving units, ensuring the pedestals are placed in the correct formation to fully support the unit.
When using plan sizes exceeding 450x450x50, advice should be taken on the suitability and use of the chosen product. For further information, please contact Group Technical Services.
Borders
The perfect edge restraints to coordinate or contrast with other products within the paving range
Jointing
Selecting the right jointing compound is vital, as every Marshalls Jointing Compound is made specifically for the material, they will be installed with to create a strong and durable finish. To help you determine the most effective jointing compound for your project, we've put together the installation matrix below. For further information or guidance, please contact Group Technical Services.
Jointing types:
- Exterior Tile Grout: Not recommended for use on a driveway, or with products laid on a flexible bed. Installation should be carried out by a landscaping professional. Based on 600 x 600 x 20 paving unit with 3mm joint. Please note: 12-month shelf life from date of manufacture.
- Exterior Jointing Grout: Based on Sawn Versuro 560 x 560 with a joint width of 10mm.
Please note: Installation should be carried out by a landscaping professional. Not recommended for use on Drivesys or products laid on a flexible bed. Please note: 12-month shelf life from date of manufacture. - WeatherPoint 365: This product is not a suitable jointing option for all paving materials. Therefore, it is not recommended for use with Granite Eclipse or porcelain paving ranges.
Coverage is a guide based on a 450 x 450 plan size with 10mm joints at 35mm deep. Minimum 20mm joint depth for paving. Please note: 24-month shelf life from date of manufacture. - Symphony Jointing Compound: Coverage varies based on joint width and paving product being installed. Minimum 20mm joint depth for paving. Please note: 24-month shelf life from date of manufacture.
- Drivesys Jointing Compound: Please note: 24-month shelf life from date of manufacture.
Green-away
Marshalls Green-Away comes in a handy 5L bottle covering up to a huge 300m2 area when using our 12L professional sprayer.
- PH neutral making it gentle and safe to use
- Removes and prevents mould, algae and lichen
- Pet friendly once dried (keep away from ponds)
- Apply on a dry day when rain is not forecast within 6 hours.
- Always apply onto a dry surface and thoroughly saturate the surface with Green-Away, then leave to activate.